Concours Dash Shelf Perfect for GPS, satellite radio, and toll pass mounting. The front panel can accommodate accessory switches and pilot lights.
Limited, annual production. Please complete a contact form April 1st if you are interested in Summer '19 delivery.
Part number C-02102 Price: $110.00
The original"Tailbrights" These high conspicuity reflective panels were developed over 18 years ago. Tailbrights are made of a unique 3-M material that appears black in daylight, but shines bright, white when illuminated be headlights at night. They add over 60 sq.in. of conspicuity to the rear of your C-10 Concours.
Your cost: $ 29.00
FAIRING POCKET KNOB - How many times have you wished you could get something out of a fairing pocket (ear plugs, tire gauge, side stand plate, windshield cleaner, etc.) without having to take your key out of the ignition switch first? !#%&+! Help is just a mouse click away.
If you can remove your lock from the compartment cover (the directions tell you how), and follow the included instructions, in a few minutes you will have easy access to your fairing pocket after installing the parts in this kit. This item sure isn't rocket science, but it is something you'll appreciate nearly every time you ride. Nothing to rust, as the hardware is stainless steel, per my usual practice.
Your cost: $ 25.00
ZG-BARS - Comfort at last. For 1987 and later Concours. These "bar backs" rotate the grips 2" closer to you. Handlebar risers (Gen-Mar risers or other brands) are required to utilize these modified bars. Stock cables and hoses are retained. Your bars are machined and returned to you in 1-2 business days after receipt. The bars can be returned to the Factory position. Engraved covers are provided to cover the mounting bolt area at the base of the bars.
Your cost: $97.00
How to try the "ZG" Bars position for yourself.
Note: You must have risers installed to do this test.
1. Loosen the pinch bolt on each bar.
2. Remove the 2 bolts at the base of each bar that locate it on the triple tree.
3. Rotate your bars toward you (when seated on the bike), so that the bar's closest hole is located between the 2 holes in the riser. Snug up the pinch bolts.This is the "ZG" bar position.
DO NOT RIDE THE MOTORCYCLE UNTIL YOUR BARS ARE RETURNED TO THE ORIGINAL POSITIONS AND ALL BOLTS ARE SECURED TO FACTORY SPECIFICATIONS.
HELMET LOCK BRACKETS - Every Concours needs them. These heavy-duty brackets are powder coated gloss black for lifetime durability. The brackets mount on the existing frame tabs where your locks are presently located. They require no tapping to install. You mount your locks to the brackets as shown in the image. All hardware is supplied and is non-rusting stainless steel. Instructions included.
Your Cost: $38.50/pr.
KAWASAKI JUNCTION BOX REPAIR FOR ZG-1000, ZX-10R, ZZR-1100, ZXR-250, ZX-700R, VN-750, ZX-600, ZX-600R & RX, EX-500, ZL-600 and others - The Junction Box is the weak link in the Concours', Ninja and Vulcan/Nomad electrical systems. J-Boxes typically fail in the 50-60,000 mile area due to stress corrosion of the relay and other solder joints, or excessive electrical loads on the relays caused by using J-Box leads or the bike's wiring harness to provide power for accessories, or the use of dielectric grease on the contacts, thus placing higher load(s) on a relay(s).
Stress corrosion causes heat buildup, and higher resistance, that eventually causes the relay/solder connection to fail. Depending on which relay fails, the headlight, accessories, or engine may be affected. Typically, these relays give some warning before failure by operating intermittently when warm/hot, but may operate normally when cold. These are the warning signs of pending failure, it's only a matter of time. Don't let J-Box failure leave you stranded - the dealers do not stock them and the cost can exceed $200.00 for a new one.
I do not check your relays and only replace the bad one(s). My service replaces all of your J-box's relays with new, higher capacity ones, thus assuring ample reserve current carrying capacity. All diodes are checked and replaced as necessary. Other soldered connections and fuse holders are repaired as necessary. Damaged/delaminated circuit board traces are repaired if possible. Circuit board, conformal coating damage is also repaired. Future stress corrosion is greatly reduced by the techniques that are used in my rebuilding process. Refurbished junction boxes are warranted for 1 year from the date of shipment. The rebuilding of your j-box takes 1-2 days after receipt. Return is by Priority Mail.
NOTE: When sending your J-box for rebuilding; remove the cover, all fuses, the fuse pulling tool, fan fuse bracket and the rubber, damper strap. Send to the address on the Contact page.
Your cost: $80.00, Exchange
Fully refurbished Concours J-box, non exchange J-box $120.00. Out of stock
Call me direct if you need expedited shipping. Shipping to Canada is extra, contact me for cost.
Used J-boxes wanted. Call for a cash price offer 561-417-3607
Buck Sport Touring
Concours C-10 Driving Light Mount. Riders desiring outstanding nighttime lighting can use this mount for long range driving lights (Hella FF-200's shown). Incandescent or HID lights are still the best for this type of lighting. Mounts manufactured in 2019 will have the "Denali" modification for increased strength for rough terrain. The brackets are mounted to the tubular steel, fairing structure - not the plastic.
The smaller, horizontal lights are LED's for daytime conspicuity, increased safety and low wattage consumption.
Please complete a contact form by April 1st to be advised of availability for Summer '19 shipment.
Part Number: C-02109 Price $120.00
Contact me for Canadian additional shipping cost.